How to Use Carprog full v8.21 Reset BMW Airbag

How to Use Carprog full v8.21 Reset BMW Airbag  , Here is the instructions help you

perfect-carprog-support-online-and-offline-2[1]

BWM airbag sensor after car crash and airbag deployment can by locked (Control unit faulty) and must be replaced. Even after small accident Airbag sensor will write in internal memory special error message “crash data stored” or “computer fault” and after you need to exchange very expensive sensor to new one. With our BMW Airbag Reset Tool you can reset and repair airbag computer in your office in 1 minute.

carprog-do-bmw-1

carprog-do-bmw-2

+/- supported units ZAE, MRSZ, MRSZ3, MRSZ4 (not all) + supported units BAE, ZAE, ZAE2, MRSZ, MRSZ2, MRSZ3, MRSZ4

There are few major types of BMW Airbag ECU`s:
1. BAE

carprog-do-bmw-3

No need to remove from car!
EEPROM read/write, Crash Data clear, Error
Memory read/erase.
Pin 9 – K line
Pin 5 – +12V
Pin 6 – GND

2. ZAE
No picture
No need to remove from car!
EEPROM read/write, Crash Data clear, Error Memory read/erase.
Pin 9 – K line
Pin 5 – +12V
Pin 6 – GND

3. ZAE2
No picture
No need to remove from car!
EEPROM read/write, Crash Data clear, Error Memory read/erase.
Pin 9 – K line
Pin 5 – +12V
Pin 6 – GND

4. MRSZ

carprog-do-bmw-4

5. MRSZ2

No need to remove from car!
EEPROM read/write, Crash Data clear, Error
Memory read/erase.
Pin 9 – K line
Pin 5 – +12V
Pin 6 – GND

6. MRSZ3 – Temic

On Board only!
EEPROM read/write, Crash Data clear, Error
Memory read/erase.
Pin 9 – K line
Pin 5 – +12V
Pin 6 – GND

carprog-do-bmw-5

7. MRSZ3 – Bosch

carprog-do-bmw-6

No need to remove from car!
EEPROM read/write, Crash Data clear, Error
Memory read/erase.
Pin 9 – K line
Pin 5 – +12V
Pin 6 – GND

8. MRSZ4 – Temic

carprog-do-bmw-7

 

No need to remove from car!
EEPROM read/write, Crash Data clear, Error
Memory read/erase.
Pin 9 – K line
Pin 5 – +12V
Pin 6 – GND

9. MRSZ4 – Bosch

carprog-do-bmw-8

 

No need to remove from car!
EEPROM read/write, Crash Data clear, Error
Memory read/erase.
Pin 9 – K line
Pin 5 – +12V
Pin 6 – GND

Using these pictures you can erase airbag “on the table” – you must connect GND, +12V,
and Diagnostic line between airbag sensor and BMW Airbag Eraser, connect power supply to GND
and +12V and use Eraser like in the car. After erasing don’t connect power supply again – BMW
airbag sensor is very sensitive and can write “controller malfunction” error after connection on the
table without car.
OBDII – BMW 20 pin connection diagram (or you can user any OBDII to BMW converter):

carprog-do-bmw-9

Done!

That’s all for the Carprog full v8.21 Reset BMW Airbag

www.obd2shop.co.uk

(Visited 177 times, 1 visits today)