Obdstar X300 DP Plus is able to program the 2019 Nissan Sylphy B18 proximity key with a free pin code by OBD. Need to work with NISSAN-40 BCM Cable for the process. Read this guide to learn how to do it.
Check the video to learn:
Preparation
Remove the trim panel under the dashboard and locate the BCM module.
Connect NISSAN-40 BCM Cable to BCM module.
Connect to Key Master DP Plus via the main cable.
Operation
CAR IMMO >> NISSAN INFINITI >> Latest Version >> Manual Select System >> 28 Digital Pincode >> SYLPHY(B18)/SENTRA >> PROXIMITY >> 2019- >> Add Keys(Free Pincode)
This function is available by connecting the server, please ensure the Internet connection is normal. Press “Enter”.
This function continues to need to unplug the gateway interface, and then use the dedicated Nissan/Renault 16+32 interface to connect to the unplugged gateway interface.
Press “Enter” to continue.
Note:
1. Executing this function will clear all the keys of the vehicle. The deleted keys must be re-programmed before they can be used normally;
2. Only 2 new keys can be programmed each time. If you need to program more than 3 keys. Please divide them into 2 operations;
3. There must be at least 1 key that can start the vehicle normally;
4. After the 4-button smart key programming is completed, if the transponder and the smart are not normal, please try to Write HEM Confin.
Warning:
1. To ensure that the pincode is successfully read, please turn on the ignition switch;
2. The device must not be disconnected during the pin code reading process. Otherwise, the module will be damaged;
3. Please check the vehicle voltage, line connection, and other conditions to prevent the device from connecting abnormally in the middle.
Press “Enter”.
Writing data, please wait for about 5 minutes…
The current 28-digit pincode has been read out.
This pin code can be used when all the keys of the current vehicle are lost to perform key programming operations.
Press “Enter”.
Turn on the double flash, and turn off the ignition switch.
Switch the ignition on.
1. Long press the start button to turn off the ignition switch;
2. Turn on the hazard warning lights(double flashing lights);
3. The gear position is in P gear or neutral gear;
4. The steering column lock is in the unlocked state.
Start to read the key ID:
Place the 1st smart key to be programmed(with the mark upward) flat above the ignition switch, the key end with the mark is directly above the ignition switch, and other smart keys are far away from the ignition switch.
Special note:
1. Do not move the key on the ignition switch;
2. Do not press any button of the smart key;
3. Do not insert or remove the blade key in the smart key.
Press “Enter”.
New key number: 0
Old key number: 1
Current total key number: 1
Note:
1. Here you need to read all key IDs to be programmed;
2. New keys can only be programmed at most 2 keys, the total number of keys is up to 4; Press “Enter” to read the next key, “Esc” to the next step.
Start programming the key:
Place the 1st smart key to be programmed(with the mark upward) flat above the ignition switch, the key end with the mark is directly above the ignition switch, and other smart keys are far away from the ignition switch.
Special note:
1. Do not move the key on the ignition switch;
2. Do not press any button of the smart key;
3. Do not insert or remove the blade key in the smart key.
Press “Enter”.
The key is being programmed, please do not move the key…
Program success.
Number of keys successfully programmed: 1
Follow the following operations to complete the programming functions:
1. Turn off the hazard warning lights(double flashing lights);
2. Press the lock and unlock button of each smart key one by one to verify whether it is normal;
3. Check one by one whether each smart key can be put into the car to start the car;
4. After completing the above operation, press “Enter” to end the function.
After all keys have been verified, please do not exit this function, press “Enter” to continue after completing the operation according to the following prompts:
1. Remove the dedicated Nissan/Renault 16+35 connector and restore the gateway module;
2. Connect the device to the vehicle OBDII connector and turn on the ignition switch.
Program success.